314 lines
11 KiB
C
314 lines
11 KiB
C
//#############################################################################
|
|
//
|
|
// FILE: device.h
|
|
//
|
|
// TITLE: Device setup for examples.
|
|
//
|
|
//#############################################################################
|
|
//
|
|
// $Release Date: $
|
|
// $Copyright:
|
|
// Copyright (C) 2014-2024 Texas Instruments Incorporated - http://www.ti.com/
|
|
//
|
|
// Redistribution and use in source and binary forms, with or without
|
|
// modification, are permitted provided that the following conditions
|
|
// are met:
|
|
//
|
|
// Redistributions of source code must retain the above copyright
|
|
// notice, this list of conditions and the following disclaimer.
|
|
//
|
|
// Redistributions in binary form must reproduce the above copyright
|
|
// notice, this list of conditions and the following disclaimer in the
|
|
// documentation and/or other materials provided with the
|
|
// distribution.
|
|
//
|
|
// Neither the name of Texas Instruments Incorporated nor the names of
|
|
// its contributors may be used to endorse or promote products derived
|
|
// from this software without specific prior written permission.
|
|
//
|
|
// THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
|
// "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
|
// LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
|
|
// A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
|
|
// OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
|
|
// SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
|
|
// LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
|
|
// DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
|
|
// THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
|
|
// (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
|
|
// OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
|
|
// $
|
|
//#############################################################################
|
|
|
|
//
|
|
// Included Files
|
|
//
|
|
#include "driverlib.h"
|
|
|
|
//*****************************************************************************
|
|
//
|
|
// Defines for pin numbers and other GPIO configuration
|
|
//
|
|
//*****************************************************************************
|
|
//
|
|
// LEDs
|
|
//
|
|
#ifdef _LAUNCHXL_F28377S
|
|
#define DEVICE_GPIO_PIN_LED1 12U // GPIO number for LD9
|
|
#define DEVICE_GPIO_PIN_LED2 13U // GPIO number for LD10
|
|
#define DEVICE_GPIO_CFG_LED1 GPIO_12_GPIO12 // "pinConfig" for LD9
|
|
#define DEVICE_GPIO_CFG_LED2 GPIO_13_GPIO13 // "pinConfig" for LD10
|
|
#else
|
|
#define DEVICE_GPIO_PIN_LED1 31U // GPIO number for LD2
|
|
#define DEVICE_GPIO_PIN_LED2 34U // GPIO number for LD3
|
|
#define DEVICE_GPIO_CFG_LED1 GPIO_31_GPIO31 // "pinConfig" for LD2
|
|
#define DEVICE_GPIO_CFG_LED2 GPIO_34_GPIO34 // "pinConfig" for LD3
|
|
#endif
|
|
|
|
//
|
|
// SCI for USB-to-UART adapter on FTDI chip
|
|
//
|
|
#ifdef _LAUNCHXL_F28377S
|
|
#define DEVICE_GPIO_PIN_SCIRXDA 85U // GPIO number for SCI RX
|
|
#define DEVICE_GPIO_PIN_SCITXDA 84U // GPIO number for SCI TX
|
|
#define DEVICE_GPIO_CFG_SCIRXDA GPIO_85_SCIRXDA // "pinConfig" for SCI RX
|
|
#define DEVICE_GPIO_CFG_SCITXDA GPIO_84_SCITXDA // "pinConfig" for SCI TX
|
|
#else
|
|
#define DEVICE_GPIO_PIN_SCIRXDA 28U // GPIO number for SCI RX
|
|
#define DEVICE_GPIO_PIN_SCITXDA 29U // GPIO number for SCI TX
|
|
#define DEVICE_GPIO_CFG_SCIRXDA GPIO_28_SCIRXDA // "pinConfig" for SCI RX
|
|
#define DEVICE_GPIO_CFG_SCITXDA GPIO_29_SCITXDA // "pinConfig" for SCI TX
|
|
#endif
|
|
|
|
//
|
|
// CANA
|
|
//
|
|
#define DEVICE_GPIO_PIN_CANTXA 31U // GPIO number for CANTXA
|
|
#define DEVICE_GPIO_PIN_CANRXA 30U // GPIO number for CANRXA
|
|
|
|
//
|
|
// CAN External Loopback
|
|
//
|
|
#define DEVICE_GPIO_CFG_CANRXA GPIO_30_CANRXA // "pinConfig" for CANA RX
|
|
#define DEVICE_GPIO_CFG_CANTXA GPIO_31_CANTXA // "pinConfig" for CANA TX
|
|
#define DEVICE_GPIO_CFG_CANRXB GPIO_10_CANRXB // "pinConfig" for CANB RX
|
|
#define DEVICE_GPIO_CFG_CANTXB GPIO_8_CANTXB // "pinConfig" for CANB TX
|
|
|
|
//I2CA GPIO pins
|
|
#define DEVICE_GPIO_PIN_SDAA 104
|
|
#define DEVICE_GPIO_PIN_SCLA 105
|
|
|
|
#define DEVICE_GPIO_CFG_SDAA GPIO_104_SDAA
|
|
#define DEVICE_GPIO_CFG_SCLA GPIO_105_SCLA
|
|
|
|
|
|
//I2CB GPIO pins
|
|
#define DEVICE_GPIO_PIN_SDAB 40
|
|
#define DEVICE_GPIO_PIN_SCLB 41
|
|
|
|
#define DEVICE_GPIO_CFG_SDAB GPIO_40_SDAB
|
|
#define DEVICE_GPIO_CFG_SCLB GPIO_41_SCLB
|
|
|
|
//*****************************************************************************
|
|
//
|
|
// Defines related to clock configuration
|
|
//
|
|
//*****************************************************************************
|
|
//
|
|
// LaunchPad Configuration
|
|
//
|
|
#ifdef _LAUNCHXL_F28377S
|
|
|
|
//
|
|
// 10MHz XTAL on controlCARD. For use with SysCtl_getClock().
|
|
//
|
|
#define DEVICE_OSCSRC_FREQ 10000000U
|
|
|
|
//
|
|
// Define to pass to SysCtl_setClock(). Will configure the clock as follows:
|
|
// PLLSYSCLK = 10MHz (XTAL_OSC) * 40 (IMULT) * 1 (FMULT) / 2 (PLLCLK_BY_2)
|
|
//
|
|
#define DEVICE_SETCLOCK_CFG (SYSCTL_OSCSRC_XTAL | SYSCTL_IMULT(40) | \
|
|
SYSCTL_FMULT_NONE | SYSCTL_SYSDIV(2) | \
|
|
SYSCTL_PLL_ENABLE)
|
|
|
|
//
|
|
// 200MHz SYSCLK frequency based on the above DEVICE_SETCLOCK_CFG. Update the
|
|
// code below if a different clock configuration is used!
|
|
//
|
|
#define DEVICE_SYSCLK_FREQ ((DEVICE_OSCSRC_FREQ * 40 * 1) / 2)
|
|
|
|
//
|
|
// ControlCARD Configuration
|
|
//
|
|
#else
|
|
|
|
//
|
|
// 20MHz XTAL on controlCARD. For use with SysCtl_getClock().
|
|
//
|
|
#define DEVICE_OSCSRC_FREQ 20000000U
|
|
|
|
//
|
|
// Define to pass to SysCtl_setClock(). Will configure the clock as follows:
|
|
// PLLSYSCLK = 20MHz (XTAL_OSC) * 20 (IMULT) * 1 (FMULT) / 2 (PLLCLK_BY_2)
|
|
//
|
|
#define DEVICE_SETCLOCK_CFG (SYSCTL_OSCSRC_XTAL | SYSCTL_IMULT(20) | \
|
|
SYSCTL_FMULT_NONE | SYSCTL_SYSDIV(2) | \
|
|
SYSCTL_PLL_ENABLE)
|
|
|
|
//
|
|
// 200MHz SYSCLK frequency based on the above DEVICE_SETCLOCK_CFG. Update the
|
|
// code below if a different clock configuration is used!
|
|
//
|
|
#define DEVICE_SYSCLK_FREQ ((DEVICE_OSCSRC_FREQ * 20 * 1) / 2)
|
|
|
|
#endif
|
|
|
|
//
|
|
// 50MHz LSPCLK frequency based on the above DEVICE_SYSCLK_FREQ and a default
|
|
// low speed peripheral clock divider of 4. Update the code below if a
|
|
// different LSPCLK divider is used!
|
|
//
|
|
#define DEVICE_LSPCLK_FREQ (DEVICE_SYSCLK_FREQ / 4)
|
|
|
|
//*****************************************************************************
|
|
//
|
|
// Macro to call SysCtl_delay() to achieve a delay in microseconds. The macro
|
|
// will convert the desired delay in microseconds to the count value expected
|
|
// by the function. \b x is the number of microseconds to delay.
|
|
//
|
|
//*****************************************************************************
|
|
#define DEVICE_DELAY_US(x) SysCtl_delay(((((long double)(x)) / (1000000.0L / \
|
|
(long double)DEVICE_SYSCLK_FREQ)) - 9.0L) / 5.0L)
|
|
|
|
//*****************************************************************************
|
|
//
|
|
// Defines, Globals, and Header Includes related to Flash Support
|
|
//
|
|
//*****************************************************************************
|
|
#ifdef _FLASH
|
|
#include <stddef.h>
|
|
|
|
extern uint16_t RamfuncsLoadStart;
|
|
extern uint16_t RamfuncsLoadEnd;
|
|
extern uint16_t RamfuncsLoadSize;
|
|
extern uint16_t RamfuncsRunStart;
|
|
extern uint16_t RamfuncsRunEnd;
|
|
extern uint16_t RamfuncsRunSize;
|
|
|
|
#define DEVICE_FLASH_WAITSTATES 3
|
|
|
|
#endif
|
|
|
|
extern uint32_t Example_PassCount;
|
|
extern uint32_t Example_Fail;
|
|
|
|
//*****************************************************************************
|
|
//
|
|
// Function Prototypes
|
|
//
|
|
//*****************************************************************************
|
|
//*****************************************************************************
|
|
//
|
|
//! \addtogroup device_api
|
|
//! @{
|
|
//
|
|
//*****************************************************************************
|
|
extern void Device_init(void);
|
|
//*****************************************************************************
|
|
//!
|
|
//!
|
|
//! @brief Function to turn on all peripherals, enabling reads and writes to the
|
|
//! peripherals' registers.
|
|
//!
|
|
//! Note that to reduce power, unused peripherals should be disabled.
|
|
//!
|
|
//! @param None
|
|
//! @return None
|
|
//
|
|
//*****************************************************************************
|
|
extern void Device_enableAllPeripherals(void);
|
|
//*****************************************************************************
|
|
//!
|
|
//!
|
|
//! @brief Function to disable pin locks on GPIOs.
|
|
//!
|
|
//! @param None
|
|
//! @return None
|
|
//
|
|
//*****************************************************************************
|
|
extern void Device_initGPIO(void);
|
|
//*****************************************************************************
|
|
//!
|
|
//! @brief Function to enable pullups for the unbonded GPIOs on the 176PTP package:
|
|
//! GPIOs Grp Bits
|
|
//! 95-132 C 31
|
|
//! D 31:0
|
|
//! E 4:0
|
|
//! 134-168 E 31:6
|
|
//! F 8:0
|
|
//!
|
|
//! @param None
|
|
//! @return None
|
|
//
|
|
//*****************************************************************************
|
|
extern void Device_enableUnbondedGPIOPullupsFor176Pin(void);
|
|
//*****************************************************************************
|
|
//!
|
|
//! @brief Function to enable pullups for the unbonded GPIOs on the 100PZ package:
|
|
//! GPIOs Grp Bits
|
|
//! 0-1 A 1:0
|
|
//! 5-9 A 9:5
|
|
//! 22-40 A 31:22
|
|
//! B 8:0
|
|
//! 44-57 B 25:12
|
|
//! 67-68 C 4:3
|
|
//! 74-77 C 13:10
|
|
//! 79-83 C 19:15
|
|
//! 93-168 C 31:29
|
|
//! D 31:0
|
|
//! E 31:0
|
|
//! F 8:0
|
|
//! @param None
|
|
//! @return None
|
|
//
|
|
//
|
|
//*****************************************************************************
|
|
extern void Device_enableUnbondedGPIOPullupsFor100Pin(void);
|
|
//*****************************************************************************
|
|
//!
|
|
//! @brief Function to enable pullups for the unbonded GPIOs on the
|
|
//! 176PTP package.
|
|
//!
|
|
//! @param None
|
|
//! @return None
|
|
//
|
|
//*****************************************************************************
|
|
extern void Device_enableUnbondedGPIOPullups(void);
|
|
//*****************************************************************************
|
|
//!
|
|
//! @brief Function to implement Analog trim of TMX devices
|
|
//!
|
|
//! @param None
|
|
//! @return None
|
|
//
|
|
//*****************************************************************************
|
|
extern void Device_configureTMXAnalogTrim(void);
|
|
//*****************************************************************************
|
|
//!
|
|
//! @brief Error handling function to be called when an ASSERT is violated
|
|
//!
|
|
//! @param *filename File name in which the error has occurred
|
|
//! @param line Line number within the file
|
|
//! @return None
|
|
//
|
|
//*****************************************************************************
|
|
extern void __error__(const char *filename, uint32_t line);
|
|
extern void Example_setResultPass(void);
|
|
extern void Example_setResultFail(void);
|
|
extern void Example_done(void);
|
|
|
|
//
|
|
// End of file
|
|
//
|