124 lines
2.9 KiB
Markdown
124 lines
2.9 KiB
Markdown
### TI C2000 TMS320F28377S Coreboard V1.3
|
|
|
|
<a href="url"><img src="./images/f28377s_coreboard_front.png" width="400"></a>
|
|
|
|
#### TMS320F28377S (LQFP100)
|
|
- Dimension: 55 mm x 55 mm
|
|
- CPUs: C28x (200 MHz)
|
|
- CLAs: Control Law Accelerator (200 MHz)
|
|
- Flash: 1023 KB
|
|
- RAM: 164 KB
|
|
|
|
#### Coreboard V1.3 On-Board Hardware Features
|
|
- External EEPROM AT24CM02: 1x (I2C-A SDA: GPIO91, I2C-A SCL: GPIO92)
|
|
- USB-to-UART: 1x (SCI-A TXD: GPIO84, SCI-A RXD: GPIO85)
|
|
- User LEDs: 2x (Red: GPIO41, Blue: GPIO58)
|
|
- GPIO Pins: 42x in total
|
|
- Analog Pins: 14x in total
|
|
|
|
#### Coreboard V1.3 GPIO and Peripheral Muxing
|
|
- SCI/UART: Up to 3x (SCI-A, SCI-B, SCI-C)
|
|
- I2C: Up to 2x (I2C-A, I2C-B)
|
|
- CAN: Up to 2x (CAN-A, CAN-B)
|
|
- SPI: Up to 3x (SPI-A, SPI-B, SPI-C)
|
|
- McBSP: Up to 1x (McBSP-B)
|
|
- EQEP: Up to 2x (EQEP1, EQEQ3)
|
|
- EPWM: Up to 15x
|
|
|
|
#### Software Configuration
|
|
- Code Composer Studio 12.8.1
|
|
- C2000Ware 5.04.00.00
|
|
- Compiler TI v22.6.1.LTS
|
|
|
|
<details>
|
|
<summary>
|
|
<b>Flashing Firmware with C2Prog</b>
|
|
</summary>
|
|
|
|
#### Step 1: Configure the Boot Switches
|
|
|
|
Set the DIP switches as follows:
|
|
|
|
- Switch 1: **ON**
|
|
- Switch 2: **OFF**
|
|
- Switch 3: **OFF**
|
|
|
|
Then connect the board to the PC using the USB port.
|
|
|
|
<a href="url">
|
|
<img src="./images/SCIA_C2Prog_flash1.png" width="600">
|
|
</a>
|
|
|
|
#### Step 2: Program the Firmware
|
|
|
|
Open **C2Prog** and configure the settings as shown in the image below.
|
|
|
|
<a href="url">
|
|
<img src="./images/C2Prog.png" width="800">
|
|
</a>
|
|
|
|
Select the compiled firmware file, then click the **Program** button to start flashing.
|
|
|
|
#### Step 3: Restore the Boot Switches
|
|
|
|
After programming is complete:
|
|
|
|
1. Disconnect the USB cable.
|
|
2. Set all DIP switches to the **ON** position:
|
|
- Switch 1: **ON**
|
|
- Switch 2: **ON**
|
|
- Switch 3: **ON**
|
|
|
|
<a href="url">
|
|
<img src="./images/SCIA_C2Prog_flash2.png" width="600">
|
|
</a>
|
|
|
|
#### Step 4: Reconnect the Board
|
|
|
|
Reconnect the USB cable to the PC for further testing and verification.
|
|
|
|
</details>
|
|
|
|
<details>
|
|
<summary>
|
|
<b>Flashing Firmware with CCS and JTAG</b>
|
|
</summary>
|
|
|
|
#### Step 1: Open the CCS Workspace
|
|
|
|
Launch **Code Composer Studio (CCS)** and open the workspace that contains your project.
|
|
|
|
#### Step 2: Import the CCS Project
|
|
|
|
From the CCS menu, select:
|
|
|
|
**Project -> Import CCS Projects**
|
|
|
|
as shown in the image below.
|
|
|
|
<a href="url">
|
|
<img src="./images/CCS_project_import.png" width="600">
|
|
</a>
|
|
|
|
Follow the prompts to select and import the desired CCS project.
|
|
|
|
#### Step 3: Build and Debug the Project
|
|
|
|
Build the project to generate the executable file.
|
|
|
|
Then connect the JTAG debugger to the target board and start a debug session to download and run the firmware.
|
|
|
|
</details>
|
|
|
|
#### Demo Project
|
|
|
|
UART: SCIA
|
|
<a href="url"><img src="./images/UART_SCIA.png" width="800"></a>
|
|
|
|
EPWM6A: 50KHz, 75% Duty Cycle
|
|
<a href="url"><img src="./images/EPWM6A.png" width="800"></a>
|
|
|
|
DACOUTB: 1KHz Sine Wave
|
|
<a href="url"><img src="./images/DACOUTB.png" width="800"></a>
|
|
|